idw – Informationsdienst Wissenschaft
Nachrichten, Termine, Experten
Nachrichten, Termine, Experten
Eliminating damages in offshore wind turbines is very expensive. When turbines are idle due to defective transmissions, repairs often require special cranes – high waves, strong winds, and poor visibility can hinder the deployment teams and further extend downtime. In the GEARFORM project, Fraunhofer IWU and its industry partners developed a hot rolling process to manufacture durable, large-module gears. In contrast to hobbing, hot rolling also boasts an outstanding material utilization rate and significantly shorter production times.
With a diameter of 500 millimeters and a module (tooth size) of 9.5 millimeters, the gear produced for the GEARFORM project is the largest gear ever made using forming technology. The project partners specially manufactured a hot rolling facility that heats the rolling blank to 1200 degrees and incorporates the teeth into the component under rotational movement. This forming process produces no chips; the volume remains constant during processing (volume consistency), saving up to 20 percent of the material. Even more impressive is the timesaving. The rolling process takes six and a half minutes, while hobbing would take about 60 minutes.
Outstanding product properties
Hot rolling has a particularly positive effect on the durability of a gear. During forming, the fiber orientation of the material is not separated but merely adapted to the geometric outer contour, which increases both the root strength (lower part of the toothing) and the load-bearing capacity of the tooth flank (contact area with other gears). Additionally, forming-induced hardening effects like the influence on dislocation density and grain refinement come into play: the plastic deformation resulting from the hot rolling process causes a significantly higher dislocation density in the metal's crystal lattice, which increases its strength and hardness. Simultaneously, grain refinement leads to enhanced toughness of the material. Subsequent heat treatment also serves to harden the gear; through machining (grinding), the surfaces of the gear finally receive their final contour.
The project "GEARFORM: Energy and resource-efficient forming of large-module gears" was funded by the Federal Ministry for Economic Affairs and Climate Action. Project partners, besides Fraunhofer IWU (coordination), include EMA-TEC GmbH, Härterei Reese Chemnitz GmbH & Co.KG, Dreiling Maschinenbau GmbH, and Flender GmbH.
Mike Lahl
Fraunhofer Institute for Machine Tools and Forming Technology IWU
Reichenhainer Str. 88
09126 Chemnitz
mike.lahl@iwu.fraunhofer.de
+49 371 5397-1350
https://www.iwu.fraunhofer.de/en/press/2024-Gearform-Robust-Gears-for-Reliable-W...
http://More Pictures and Video Material Available (IWU Homepage)
Offshore wind turbines are particularly efficient and contribute significantly to CO2-neutral power ...
© iStock/homeworks255
Transmission damages in offshore wind turbines are expensive – using highly durable gears like those ...
© Fraunhofer IWU
Press Release
Merkmale dieser Pressemitteilung:
Journalisten
Energie, Maschinenbau, Umwelt / Ökologie, Wirtschaft
überregional
Forschungsergebnisse, Forschungsprojekte
Englisch
Sie können Suchbegriffe mit und, oder und / oder nicht verknüpfen, z. B. Philo nicht logie.
Verknüpfungen können Sie mit Klammern voneinander trennen, z. B. (Philo nicht logie) oder (Psycho und logie).
Zusammenhängende Worte werden als Wortgruppe gesucht, wenn Sie sie in Anführungsstriche setzen, z. B. „Bundesrepublik Deutschland“.
Die Erweiterte Suche können Sie auch nutzen, ohne Suchbegriffe einzugeben. Sie orientiert sich dann an den Kriterien, die Sie ausgewählt haben (z. B. nach dem Land oder dem Sachgebiet).
Haben Sie in einer Kategorie kein Kriterium ausgewählt, wird die gesamte Kategorie durchsucht (z.B. alle Sachgebiete oder alle Länder).
