idw – Informationsdienst Wissenschaft
Nachrichten, Termine, Experten
Nachrichten, Termine, Experten
idw - Informationsdienst
Wissenschaft
Components are subject to multi-axial loadings. The typical design approach is based on material specific modelling and suitable tests to identify the parameters of the model. The tests are costly and time consuming. Scientists at the Fraunhofer Institute for Structural Durability and System Reliability LBF have suggested a basic approach to select the necessary tests for reliable modelling.
Using proposed stress analysis, the available stress states in the components under loadings can be sorted and the volumes of the components under tension and compression can be taken into account. The decision on the necessary tests is taken depending on the relation of the tension and compression loaded volumes. This method leads to reliable component design with minimum experimental costs.
Tension/Compression Differences
Common engineering design is based on the HOOKE’s law. The tensile test has become generally accepted for the identification of material data. The tension / compression differences are often neglected in conventional solutions although most construction materials are stiffer in compression as in tension. The neglecting reason is that the additional compression tests cause extra costs.
Fraunhofer LBF have implemented the method to decide when, in addition to the tensile tests, the compression tests are necessarily required. On the basis of this decision, the simulation tools can be used in accordance with the material. The reliable design solutions for optimized structures can be achieved.
Stress Analysis
Proper stress analysis helps in optimizing component design. Fraunhofer LBF’s analysis is based on the sum of the normal stresses or the first invariant of the stress tensor. If this sum is less than zero, the corresponding volume of the component is compressed and vice versa. The next step is to compare tensile and compression loaded volumes.
Suggested stress analysis enables the choice of the appropriate material model. If the volume of the component under tension is significantly greater as under compression, the standard models without tension / compression differences can be used for design. This avoids further tests.
The application of the method is shown with the practical example of a cable clamp under relevant loading: Due to biplane symmetry, one fourth of the component is taken for analysis.
The volumes under tension and compression in the cable clip are identified in simulation. Plots are presented for the sign of first invariant. It is clear that the volume of the component under tension and compression are comparable. In this case, the effect of different material properties at tension and compression is considerable and should be taken into account. In addition to the tensile tests, the compression tests are highly recommended.
With this analysis, the Fraunhofer LBF supports numerous small and middle-sized entrepreneurs in their competitive. The experimental costs are adjusted to the usage of the component. Simple assignment of loaded components based on the first stress invariant delivers accurate information for utilization of material-specific properties.
Dr.-Ing. Vladimir A. Kolupaev, Vladimir.Kolupaev@lbf.fraunhofer.de
Dipl.-Ing. (FH) Axel Nierbauer, axel.nierbauer@lbf.fraunhofer.de
Merkmale dieser Pressemitteilung:
Journalisten, Wirtschaftsvertreter
Chemie, Maschinenbau, Werkstoffwissenschaften
überregional
Forschungs- / Wissenstransfer, Forschungsergebnisse
Englisch
Sie können Suchbegriffe mit und, oder und / oder nicht verknüpfen, z. B. Philo nicht logie.
Verknüpfungen können Sie mit Klammern voneinander trennen, z. B. (Philo nicht logie) oder (Psycho und logie).
Zusammenhängende Worte werden als Wortgruppe gesucht, wenn Sie sie in Anführungsstriche setzen, z. B. „Bundesrepublik Deutschland“.
Die Erweiterte Suche können Sie auch nutzen, ohne Suchbegriffe einzugeben. Sie orientiert sich dann an den Kriterien, die Sie ausgewählt haben (z. B. nach dem Land oder dem Sachgebiet).
Haben Sie in einer Kategorie kein Kriterium ausgewählt, wird die gesamte Kategorie durchsucht (z.B. alle Sachgebiete oder alle Länder).
